Projector and screen calculator: distance, size and brightness
Work out how far to place the projector, how high the lens goes and whether your lumens are enough for the screen you want, with a drawing you can move.
Drag the projector, or use the arrow keys. The bar on the ceiling is the lens zoom range and the one on the floor is the ideal seating zone.
Image brightness
Fine tuning
Results
32.8 fL
Plenty of brightness
With 2000 lm on a 120″ image you reach 32.8 fL: more than a dark room needs (12–22 fL). That gives you headroom if the room is not fully dark, or you can enlarge the screen up to 184″ and hold 14 fL.
- Distance with your lens zoom
- 12.2 – 18.3 ft (3.72 – 5.58 m)
- Your distance (14.8 ft (4.50 m)) is within the lens zoom range.
- Image size
- 8.7 × 4.9 ft (2.66 × 1.49 m)
- 120″ at 16:9
- Lens height
- 7.7 ft (2.34 m)
- 1.2 ft (0.36 m) below the ceiling.
- Recommended lumens
- 850 – 980 lm
- for 14–16 fL, with 30% loss and 1 gain
- Largest screen for your lumens
- 184″
- the largest screen that keeps 14 fL with 2000 lm
- Seating distance
- 12.0 – 16.3 ft (3.65 – 4.96 m)
- the image fills between 40° and 30° of your field of view
Planning a home theater?
We integrate the screen, projector, audio and lighting control from the plans. Tell us about your room and we will advise you.
Estimate for guidance. The final design is set by measuring the room on site.
Before you buy a projector or open the ceiling, three questions need an answer: how far from the screen it goes, how high the lens sits, and whether the lumens are enough for the size you want. The calculator above answers them together. Drag the projector in the drawing and watch how the zoom you need, the lens height and the brightness of the image change.
How to use the calculator
- Pick the diagonal and the image format: 16:9 or widescreen (2.35:1 or 2.40:1). The diagonal is the image diagonal, not the frame.
- Copy from the projector spec sheet the lumens and the throw ratio, for example 1.4–2.1:1.
- Move the projector in the drawing, with your finger or the arrow keys, or type the distance. The bar on the ceiling shows how far the lens zoom reaches; the one on the floor shows where to sit.
- Check the lens height against the ceiling and the brightness gauge.
- Copy the link to share the result with whoever installs the equipment.
What each result measures
- Distance with your lens zoom. The throw ratio is the projector distance divided by the image width. With an image 8.7 ft (2.66 m) wide (120″ at 16:9) and a zoom of 1.4 to 2.1:1, the projector goes between 12.2 and 18.3 ft (3.72 and 5.58 m) from the screen. Closer, the image does not fill the screen; farther, it spills past it.
- Lens height. It comes from the bottom edge of the screen, the image height and the lens offset. Here the offset is the percentage of the image height by which the lens sits above the top edge (negative if it sits below). If your projector spec sheet measures it from the center of the image, subtract 50 points.
- Brightness. The light reaching the screen is measured in foot-lamberts (fL): lumens × (1 − loss) × gain ÷ image area in square feet. 14 fL (about 48 cd/m²) is the digital cinema reference, and a dark room is usually put at 12 to 22 fL.
- Recommended lumens. The spec-sheet lumens you need to land between 14 and 16 fL with the loss and gain you set.
- Largest screen for your lumens. The biggest diagonal that keeps 14 fL.
- Seating distance. The one that makes the image fill between 40° and 30° of your field of view, as in the TV viewing distance calculator.
Projector distance by size
For 16:9 images and a sample throw ratio of 1.4 to 2.1:1. The range for your projector is on its spec sheet: change it in the calculator to see yours.
| Diagonal | Image (width × height) | Projector distance |
|---|---|---|
| 100″ | 7.3 × 4.1 ft (2.21 × 1.25 m) | 10.2 – 15.3 ft (3.10 – 4.65 m) |
| 110″ | 8.0 × 4.5 ft (2.44 × 1.37 m) | 11.2 – 16.8 ft (3.41 – 5.11 m) |
| 120″ | 8.7 × 4.9 ft (2.66 × 1.49 m) | 12.2 – 18.3 ft (3.72 – 5.58 m) |
| 135″ | 9.8 × 5.5 ft (2.99 × 1.68 m) | 13.7 – 20.6 ft (4.18 – 6.28 m) |
| 150″ | 10.9 × 6.1 ft (3.32 × 1.87 m) | 15.3 – 22.9 ft (4.65 – 6.97 m) |
Brightness and seating by size
Spec-sheet lumens to land between 14 and 16 fL, with 30% loss and a white screen of gain 1.0, and the seating distance for the image to fill between 40° and 30° of your view.
| Diagonal | Spec-sheet lumens | Seating distance |
|---|---|---|
| 100″ | 590 – 680 lm | 10.0 – 13.6 ft (3.04 – 4.13 m) |
| 110″ | 720 – 820 lm | 11.0 – 14.9 ft (3.35 – 4.54 m) |
| 120″ | 850 – 980 lm | 12.0 – 16.3 ft (3.65 – 4.96 m) |
| 135″ | 1080 – 1240 lm | 13.5 – 18.3 ft (4.11 – 5.58 m) |
| 150″ | 1340 – 1530 lm | 15.0 – 20.3 ft (4.56 – 6.20 m) |
With 2000 spec-sheet lumens, the largest screen that keeps 14 fL is about 184″.
An example
A 120″ image at 16:9, a 2000 lm projector with a 1.4 to 2.1:1 zoom, and the projector 14.8 ft (4.5 m) from the screen. The projector is within the zoom range (12.2 to 18.3 ft), brightness is 32.8 fL, more than a dark room needs, and with the sofa also 14.8 ft (4.5 m) from the screen the image fills about 33° of your field of view.
If you move up to 150″, brightness falls to 21.0 fL, still in range. But the projector would need to sit at 15.3 ft (4.65 m) or more: at 14.8 ft (4.5 m) it falls 0.5 ft (15 cm) short and the image would not fill the screen. The calculator shows this kind of clash before you buy.
What else matters
- Ambient light. The calculator assumes a dark room. With ambient light the image needs more brightness.
- Spec-sheet lumens. They are usually measured in the projector’s brightest mode. In cinema mode and after calibration the image is less bright, so the calculator subtracts a loss, which starts at 30% and you can change under Fine tuning.
- Screen gain. A screen with gain above 1.0 sends more light straight ahead, at the cost of a narrower viewing angle. A lower one spreads it more.
- Zoom extremes. Leave some margin from the ends of the range instead of fitting the distance to the limit.
- Obstructions. Beams, light fixtures and air-conditioning ducts: check that neither the light beam nor the projector runs into anything.
How it is calculated
- Image width and height:
W = D · 0.0254 · r / √(1 + r²)andH = W / r, withDthe diagonal in inches andrthe aspect ratio (16/9, 2.35 or 2.40). - Projector distance:
d = throw ratio × W. - Brightness:
fL = lm · (1 − loss) · gain ÷ (W · H), with the area in square feet (1 m² = 10.764 ft²). - Lumens for a target:
lm = fL · (W · H) ÷ ((1 − loss) · gain). - Lens height:
bottom edge + H · (1 + offset). - Seating distance:
d = W / (2 · tan(θ / 2)), withθ= 40° and 30°.
The 14 fL reference comes from SMPTE ST 431-1 for digital cinema. The 30° and 40° of field of view are SMPTE and THX recommendations, not mandatory standards. The results are an estimate: confirm the dimensions with the spec sheet of the projector and screen you choose.
Frequently asked questions
How many lumens do I need for a 120-inch screen?
To land between 14 and 16 fL in a dark room, about 850 to 980 spec-sheet lumens, with 30% loss and a white screen of gain 1.0. With ambient light you need more.
How far do I place the projector for 100 inches?
With a 1.4 to 2.1:1 zoom, between 10.2 and 15.3 ft (3.10 and 4.65 m) from the screen. Replace the throw ratio with your projector’s to see its real range.
How high does a ceiling projector go?
It depends on the screen and the lens offset. With a 120″ screen whose bottom edge sits 2.3 ft (0.70 m) off the floor and the lens 10% above the top edge, the lens sits at 7.7 ft (2.34 m): 1.2 ft (0.36 m) below an 8.9 ft (2.70 m) ceiling.
What if my projector falls outside the zoom range?
If it sits closer, the image does not fill the screen; if it sits farther, it spills past it. You can move the projector, change the screen size or choose a projector with a different zoom.
Projector or TV?
It depends on the size and the light in the room. Start with the TV viewing distance calculator: when the room calls for a bigger image than the largest TV you can get, a projector with a screen is the usual answer.
Designing a home theater?
At DomuLab we integrate the screen, projector, audio and lighting control from the plans. If you already have your room measurements, tell us and we will advise you. To see how it all fits together, read the guide to home theater with Dolby Atmos and our home theater service.





